6EP7133-6AE00-0BN0 Siemens SIMATIC ET 200SP PS 24V/10A


  • 6EP7133-6AE00-0BN0
  • SIMATIC ET 200SP PS 24V/10A
  • Regulated power supply
  • Input: 120/230 V AC
  • Output: 24 V DC/10 A

Siemens SIMATIC ET 200SP PS 24V/10A – 6EP7133-6AE00-0BN0


In terms of design and functionality, the SIMATIC ET 200SP PS single-phase load power supply with automatic range switching of the input voltage is perfectly matched to the SIMATIC ET 200SP. The SIMATIC component and the power supply are wired by means of uniform push-in terminal technology. The 24 V supply provides power to the ET 200SP system components such as the interface module, technology module and communication module, as well as the digital or analog inputs/outputs. Comprehensive certifications, such as UL or GL, facilitate universal use. Its extremely flat design also makes this power supply ideally suited for installation in compact on-site control boxes.


  • Mounting of the ET 200SP power supply on DIN rail to the left of the SIMATIC ET 200SP component
  • Direct mounting side-by-side is possible for the modules;
    Exception: SIMATIC ET 200SP component has PROFINET connector mounted on the left → 5 mm spacer required
  • Three separate load circuit connectors for easy commissioning and maintenance
  • Diagnostic LED for indicating “Output voltage 24 V DC O.K.”
  • On/off switch for isolated replacement of SIMATIC ET 200SP modules


  • Connection to all 1-phase 50/60 Hz networks (85 V… 132 V/170 V… 264 V) through automatic range switching
  • Adjustable output voltage for compensating voltage drops
  • Short-term mains buffering
  • Signal contact for further processing of “Output voltage 24 V DC O.K.” in the controller
  • Current monitor for further processing of the present energy consumption in the controller
  • Output voltage 24 V DC, stabilized, short circuit-proof, open circuit-proof
  • Parallel connection of two power supplies for enhanced performance
  • High degree of efficiency up to 90%
  • Temperature range -30 °C…+60°C/70 °C with derating
  • Easy connection of loads with high power requirements through excellent overload behavior

Technical specifications



SIMATIC ET 200SP PS 24V/10A Stabilized power supply Input: 120/230 V AC Output: 24 V DC/10 A


DataSheet in PDF

Weight 0.700 kg
Dimensions 123.00 × 185.00 × 80.00 mm



1-phase AC

supply voltage

● 1 at AC rated value

120 V

● 2 at AC rated value

230 V

input voltage

● 1 at AC

85 … 132 V

● 2 at AC

170 … 264 V

Wide-range input


Overvoltage resistance

2.3 × Vin rated, 1.3 ms

Mains buffering

at Vin = 93/187 V

Mains buffering at Iout rated, min.

20 ms; at Vin = 93/187 V

Rated line frequency 1

50 Hz

Rated line frequency 2

60 Hz

Rated line range

47 … 63 Hz

input current

● at rated input voltage 120 V

4.34 A

● at rated input voltage 230 V

1.92 A

Switch-on current limiting (+25 °C), max.

60 A

I²t, max.

6.3 A²·s

Built-in incoming fuse

T 6.3 A/250 V (not accessible)

Protection in the mains power input (IEC 898)

recommended LS switch: B/C 10 A/6 A


Controlled, isolated DC voltage

Rated voltage Vout DC

24 V

● output voltage at output 1 at DC rated value

24 V

Total tolerance, static ±

3 %

Static mains compensation, approx.

0.1 %

Static load balancing, approx.

1 %

Residual ripple peak-peak, max.

150 mV

Residual ripple peak-peak, typ.

50 mV

Spikes peak-peak, max. (bandwidth: 20 MHz)

240 mV

Spikes peak-peak, typ. (bandwidth: 20 MHz)

150 mV

Adjustment range

22.8 … 28 V

product function output voltage adjustable


Output voltage setting

via potentiometer

Status display

Green LED for 24 V OK


Relay contact (NO contact, rating 60 V DC/ 0.3 A) for "24 V OK"

On/off behavior

Overshoot of Vout < 3 %

Startup delay, max.

0.3 s

Voltage rise, typ.

30 ms

Rated current value Iout rated

10 A

Current range

0 … 12 A

● Note

10 A up to +60°C; +60 … +70 °C: Derating 3%/K

supplied active power typical

240 W

short-term overload current

● on short-circuiting during the start-up typical

30 A

● at short-circuit during operation typical

30 A

duration of overloading capability for excess current

● on short-circuiting during the start-up

750 ms

● at short-circuit during operation

800 ms

Parallel switching for enhanced performance


Numbers of parallel switchable units for enhanced performance


Efficiency at Vout rated, Iout rated, approx.

90 %

Power loss at Vout rated, Iout rated, approx.

26 W

power loss [W] during no-load operation maximum

2.8 W

Dynamic mains compensation (Vin rated ±15 %), max.

0.3 %

Dynamic load smoothing (Iout: 10/90/10 %), Uout ± typ.

3 %

Load step setting time 10 to 90%, typ.

1 ms

Load step setting time 90 to 10%, typ.

1 ms

Output overvoltage protection

protection against overvoltage in case of internal fault Vout < 31.8 V

Current limitation

14 … 15 A

property of the output short-circuit proof


Short-circuit protection

Constant current characteristic

enduring short circuit current RMS value

overcurrent overload capability in normal operation

overload capability 150 % Iout rated up to 5 s/min

Overload/short-circuit indicator

Primary/secondary isolation


galvanic isolation

Safety extra-low output voltage Uout acc. to EN 60950-1 and EN 50178

Protection class

Class I

leakage current

● maximum

3.5 mA

● typical

1 mA

Degree of protection (EN 60529)


CE mark


UL/cUL (CSA) approval

cULus-Listed (UL61010-2-201, CSA C22.2 No.142), cCSAus (CSA C22.2 No. 60950-1, UL 60950-1)

Explosion protection

IECEx Ex ec nC IIC T3 Gc; ATEX (EX) II 3G Ex ec nC IIC T3 Gc

certificate of suitability NEC Class 2


CB approval


certificate of suitability EAC approval


Marine approval


Emitted interference

EN 61000-6-3 Class B

Supply harmonics limitation

EN 61000-3-2

Noise immunity

EN 61000-6-2

ambient temperature

● during operation

-30 … +70 °C

— Note

with natural convection

● during transport

-40 … +85 °C

● during storage

-40 … +85 °C

Humidity class according to EN 60721

Climate class 3K3, 5 … 95% no condensation

Connection technology

Push-in terminals


● Supply input

L, N, PE: 1 push-in terminal each for 0.2 … 2.5 mm² single-core/finely stranded

● Output

+, -: 2 push-in terminals each for 0.2 … 2.5 mm²

● Auxiliary

Signaling contact: 2 push-in terminals for 0.2 … 2.5 mm²

● signaling contact

2 push-in terminals for 0.2 … 2.5 mm²

product function

● removable terminal at input


● removable terminal at output


width of the enclosure

160 mm

height of the enclosure

117 mm

depth of the enclosure

74 mm

required spacing

● top

50 mm

● bottom

50 mm

● left

0 mm

● right

0 mm

Weight, approx.

0.7 kg

product feature of the enclosure housing can be lined up



Snaps onto DIN rail EN 60715 35×7.5/15

electrical accessories

Redundancy module, buffer module, selectivity module, DC UPS

MTBF at 40 °C

1 114 510 h

other information

Specifications at rated input voltage and ambient temperature +25 °C (unless otherwise specified)


There are no reviews yet.

Be the first to review “6EP7133-6AE00-0BN0 Siemens SIMATIC ET 200SP PS 24V/10A”
Shopping Cart