6AG2241-1CH30-1XB0 Siemens SIPLUS S7-1200 CB 1241 RS 485 Rail Original Brand New
$423.09
6AG2241-1CH30-1XB0
Siemens SIPLUS S7-1200 CB 1241 RS 485 rail based on 6ES7241-1CH30-1XB0 with conformal coating, -25…+55 °C, OT1 with ST1/2 (+70 °C für 10 minutes), RS-485, terminal block, supports Freeport
[ez-toc]
Overview
- For fast, high-performance serial data exchange via point-to-point connection
- Approved in accordance with the EN 50155, EN 15121, EN 50124, EN 50125 and EN 45545 railway standards for use in rail traffic
- Implemented protocols: ASCII, USS drive protocol, Modbus RTU
- Additional protocols can be loaded later
- Simple parameterization with STEP 7 Basic
- Can be plugged directly into the CPU
Application
The Communication Board CB 1241 RS 485 is used for fast, high-performance serial data exchange via point-to-point connections.
Point-to-point coupling is possible, for example, to:
- SIMATIC S7 automation systems and systems of many other manufacturers
- Printers
- Robot controls
- Modems
- Scanners
- Bar code readers, etc.
The Communication Board CB 1241 RS 485 can be plugged directly into all SIMATIC S7-1200 CPUs.
This provides users with the following advantages:
- Optimal adaptation:
With communication boards, users can optimally adapt their controllers even to more complex tasks. - Flexibility:
If the task is expanded subsequently, the controller can be upgraded. Updating of the user program is extremely simple. - Use where space is limited:
The communication boards are directly plugged into the CPU, enabling the controller to be expanded without taking up any additional space.
Design
The communication boards are plugged straight into the holder on the front of the S7-1200 CPU.
- Installation:
Communication boards are plugged directly into the SIPLUS extreme S7-1200 RAIL-CPU, and are thus connected electrically and mechanically with the CPU. - The installation dimensions of the CPU remain unchanged.
- Replacement of all communication boards is facilitated by removable terminals (“permanent wiring”).
Function
On the Communication Board CB 1241 RS 485, the following standard protocols are available:
- ASCII:
For interfacing to third-party systems with simple transmission protocols, e.g. protocols with start and end characters or with block check characters. The interface handshake signals can be queried and controlled via the user program. - Modbus:
For communication according to the Modbus protocol with RTU format:- Modbus master:
Polling system with SIMATIC S7 as master. - Modbus device:
Polling system with SIMATIC S7 as device; device-to-device message frame traffic is not possible.
- Modbus master:
- USS drive protocol:
Instructions for connection of USS protocol drives are specifically supported. In this case, drives exchange data over RS485. It is then possible to control these drives, and to read and write parameters.
Additional drivers can also be downloaded.
Parameterization
The parameterization of the Communication Board CB 1241 is particularly user-friendly and simple with STEP 7 Basic:
The user specifies the properties of the module by means of a parameterization environment integrated into STEP 7 Basic.
6AG2241-1CH30-1XB0
Siemens SIPLUS S7-1200 CB 1241 RS 485 rail based on 6ES7241-1CH30-1XB0 with conformal coating, -25…+55 °C, OT1 with ST1/2 (+70 °C für 10 minutes), RS-485, terminal block, supports Freeport
Visit 6AG2241-1CH30-1XB0
For more our products visit turll.com
| Weight | 0.024 kg |
|---|---|
| Dimensions | 50 × 81 × 30 mm |
You must be logged in to post a review.
Reviews
There are no reviews yet.